1 Channel Video fiber multiplexer

Description

Model name:BD-DV10000

Product function:

The video fiber multiplexer transmit 1 channel digital video broadcasting, 1 channel high-fidelity audio, 1channel asynchronous date,1 channel 10/100M adapt Ethernet date to one fiber efficiently. With complete digital and technology, DV 1000series support any high resolution dynamic or stationary picture high-fidelity transmit. It also can be anti-disturbance against several signals, environment, and work stably .It is widely used in security monitoring and control, high way, electronic police, automation, intelligent residential districts and so on.

It can work shortly after it is installed. You could select any date interface by set. It is connected easily and it can indicate power supply, link, video, also adjust video. There are two ways to install: desktop and rack.

Features:

●   technical design, the whole surface by decoration.

●   electrical circuit is designed by hardware scheme (except chip), and production is not effected by purchasing.

●   Complete digital fiber transmit platform.

●   No need to adjust when opened.

●   Based on self copyright IC.

●   No disturbance by analog in adjusting channel, picture and range.

●   4 steps filtering

●   Complete digital, broadcast transmit efficiently

●   High speed 10/100M Ethernet channel.

●   Full speed asynchronous date channel

●   Elastic configuration on the same platform.

●   Power supply, link, video by dynamic indication.

●   Self-adapt in PAL,NTSC,SECAM.

●   ASIC design

●   Farthest transmit distance:100KM

●   Power supply:220v,-48v,+24, +12v,+5(optional)

●   The two poles of Direct power supply can be exchanged.

●   Support SNMP management in our chassis installation.

●   Three installations: wall method, rack in 19inches 1U, or plug in-card.

•  Applied field
  Intelligent transportation system;
  high speed way video monitoring and control system;
  toll monitoring and control system;
  close circuit TV industry monitoring and control;
  TV program switching channel transmit;
  high-fidelity video conference system;
  security monitoring and control system.
  Technical parameter:
  Video interface 1/2/4/8/16 line
  input/output impedance: BNC 75ohm unbalance interface
  input/output voltage: peak 1 vpp, max 1.5 Vpp
  Signal: PAL/NTSC/SECAM
  Video bandwidth: 8MHZ
  Video number wide: 8/10/12 bit
  Differential gain: <1%
  Differential phase: <0.6°
  Slope: <0.5%
  luminance delay inequality: 10ns
  luminance gain gap: ±10%
  Weighted noise ratio :66db
  Date interface
• Physical interface: industry standard terminal lead
  Work way:  full duplex/half duplex
  Interface type: RS-232/485/422,Manchester
  RS232 rate: 0-115.2Kbps
  RS-422/485 rate: 0-115.2Kbps
  RS-422/485 transmit distance: 0-1200m
  RS-422/485 agreement  support RS-485/422 agreement
  Error rate: <10-9
  Fiber interface
  Physical interface: FC/PC, ST/PC
  Fiber type: single/multi module
  Transmit distance: multi module with 0-2km,single module with 0-25km,0-60km,0-100km
  Audio interface
  audio input/output: impedance 600ohm balance/unbalance interface,industry standard terminal lead.
  audio input/output level :2Vp-p
  frequency response :10HZ-20KHZ
  audio number width :24 bit
  Weighted noise ratio: 80db
  Total Harmonic Distortion :0.1%
  Ethernet interface:
  Physical interface: shielding RJ-45
  support  IEEE 802.3/802.3u/802.1q VLAN
  work way : IEEE 802.3x full duplex and Back-Pressure half duplex flow control.
  Work environment:
  Work temperature: -30C~+75C
  storage temperature: -45C~+85C
  humidity : 0~95% without condensation
  input voltage :220V, -48V, +24V, +12V, +5V optional
  power <=5W (single terminal)

Qustion: How many kinds interface does the video fiber mux device support?

Answer: The video fiber mux can support Video/Audio/ethernet/data/pots interface,Audio/ethernet/data/pots are optional interface,customer need to notice our company when place order.

Qustion: Are the ransmitter and receiver on one same device??

Answer: No,it’s sperated. The transmitters is a device connecting with your camera,the receiver is another device connectiong to monitor.

Qustion:Do the optical video ransmitter and the optical video receiver need to work together?

Answer: yes,the transmitter and the receiver need work together,they need to work as pair.