Copper SFP module 100base-T transceiver
Short Description:
1. Copper SFP module DESCRIPTION The BDTR-FB-P1RC Copper SFP Module is a high-performance, hot-pluggable Small Form-factor Pluggable (SFP) transceiver designed for 10Base-T and 100Base-Tx Ethernet applications. Based on the SFP Multi Source Agreement (MSA), this module is fully compliant with IEEE 802.3 standards for copper connections. With a compact RJ-45 …Description
Specification
Application
Order
Downloads/FAQ
Product Tags
Reviews
Description
1. Copper SFP module DESCRIPTION
The BDTR-FB-P1RC Copper SFP Module is a high-performance, hot-pluggable Small Form-factor Pluggable (SFP) transceiver designed for 10Base-T and 100Base-Tx Ethernet applications. Based on the SFP Multi Source Agreement (MSA), this module is fully compliant with IEEE 802.3 standards for copper connections. With a compact RJ-45 connector assembly and a single +3.3V power supply, it provides seamless Fast Ethernet connectivity over Cat 5 cables. The Copper SFP Module supports extended operating temperatures from -40°C to +85°C, making it suitable for a wide range of environments. Its RoHS compliance ensures a lead-free, environmentally-friendly product that meets global standards. Whether you’re upgrading your network or adding more ports, this copper SFPs module offers reliable performance and durability.
2. PRODUCT FEATURES
Supports 10Base-T / 100Base-Tx Ethernet for reliable Fast Ethernet connections.
Hot-pluggable SFP footprint for easy installation and replacement without system downtime.
Compact RJ-45 connector assembly ensures compatibility with standard Ethernet network cables (Cat 5).
RoHS compliant and lead-free design, meeting global environmental and safety standards.
Operates with a single +3.3V power supply for energy efficiency.
10/100Base-Tx Fast Ethernet over Cat 5 cable provides cost-effective networking solutions.
Extended operating temperature range of -40°C to +85°C for rugged use in various environmental conditions.
3. Cable Length
| Line Side | Cable | Reach | Host Interface |
| 10base-T | CAT5 | 200m | 100base-FX |
| 100base-Tx | CAT5 | 100m | 100base-FX |
4. SFP to Host Connector Pin Out
| Pin | Symbol | Name/Description | Ref. |
| 1 | VEET | Transmitter Ground (Common with Receiver Ground) | 1 |
| 2 | TFAULT | Transmitter Fault. Not supported. | |
| 3 | TDIS | Transmitter Disable. Laser output disabled on high or open. | 2 |
| 4 | MOD_DEF(2) | Module Definition 2. Data line for Serial ID. | 3 |
| 5 | MOD_DEF(1) | Module Definition 1. Clock line for Serial ID. | 3 |
| 6 | MOD_DEF(0) | Module Definition 0. Grounded within the module. | 3 |
| 7 | Rate Select | No connection required | |
| 8 | LOS | High indicates no linked. low indicates linked. | 4 |
| 9 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
| 10 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
| 11 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
| 12 | RD- | Receiver Inverted DATA out. AC Coupled | |
| 13 | RD+ | Receiver Non-inverted DATA out. AC Coupled | |
| 14 | VEER | Receiver Ground (Common with Transmitter Ground) | 1 |
| 15 | VCCR | Receiver Power Supply | |
| 16 | VCCT | Transmitter Power Supply | |
| 17 | VEET | Transmitter Ground (Common with Receiver Ground) | 1 |
| 18 | TD+ | Transmitter Non-Inverted DATA in. AC Coupled. | |
| 19 | TD- | Transmitter Inverted DATA in. AC Coupled. | |
| 20 | VEET | Transmitter Ground (Common with Receiver Ground) | 1 |
Notes:
- Circuit ground is connected to chassis ground
- PHY disabled on TDIS > 2.0V or open, enabled on TDIS< 0.8V
- Should be pulled up with 4.7k – 10k Ohms on host board to a voltage between 2.0 V and 3.6 V. MOD_DEF(0) pulls line low to indicate module is plugged in.
- LVTTL compatible with a maximum voltage of 2.5V.
Figure 1. Diagram of host board connector block pin numbers and names
-
+3.3V Volt Electrical Power Interface
The BDTR-FB-P1RC has an input voltage range of 3.3 V +/- 5%. The 4V maximum voltage is not allowed for continuous operation.
| +3.3 Volt Electrical Power
Interface |
||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Supply Current | Is | – | 300 | mA | 1.0W max power over
full range of voltage and temperature. See caution note below |
|
| Input Voltage | Vcc | 3.13 | 3.3 | 3.47 | V | Referenced to GND |
| Maximum Voltage | Vmax | 4 | V | |||
| Surge Current | Isurge | TBD | mA | Hot plug above steady state
current. See caution note below |
||
Caution: Power consumption and surge current are higher than the specified values in the SFP MSA
6. Low-Speed Signals
MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA), are open drain CMOS signals (see section VII, “Serial Communication Protocol”). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc
| Low-Speed Signals, Electronic Characteristics | |||||
| Parameter | Symbol | Min | Max | unit | Notes/Conditions |
| SFP Output LOW | VOL | 0 | 0.5 | V
|
4.7k to 10k pull-up to host_Vcc,
measured at host side of connector |
| SFP Output HIGH | VOH | host_Vcc -0.5 | host_Vcc + 0.3 | V
|
4.7k to 10k pull-up to host_Vcc,
measured at host side of connector |
| SFP Input LOW | VIL | 0 | 0.8 | V | 4.7k to 10k pull-up to Vcc,
measured at SFP side of connector
|
| SFP Input HIGH | VIH | 2 | Vcc + 0.3 | V | 4.7k to 10k pull-up to Vcc,
measured at SFP side of connector |
7. High-Speed Electrical Interface
All high-speed signals are AC-coupled internally.
| High-Speed Electrical Interface, Transmission Line-SFP | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Line Frequency | fL | 125 | MHz | 5-level encoding, per
IEEE 802.3 |
||
| Tx Output Impedance | Zout,TX | 100 | Ohm | Differential, for all
frequencies between 1MHz and 125MHz |
||
| Rx Input Impedance | Zin,RX | 100 | Ohm | Differential, for all
frequencies between 1MHz and 125MHz |
||
| High-Speed Electrical Interface, Host-SFP | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Single ended data input
swing |
Vinsing | 250 | 1200 | mV
|
Single ended | |
| Single ended data output
swing |
Voutsing | 350 | 800 | mV | Single ended | |
| Rise/Fall Time | Tr,Tf | – | psec | 20%-80% | ||
| Tx Input Impedance | Zin | 50 | Ohm | Single ended | ||
| Rx Output Impedance | Zout | 50 | Ohm | Single ended | ||
8. Copper SFP module Specifications
| General | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Data Rate | BR | 10 | 100 | Mb/sec | IEEE 802.3 compatible.
See Notes 1,2 below |
|
Notes: 1. Clock tolerance is +/- 50 ppm
9. Environmental Specifications
Automatic crossover detection is enabled. External crossover cable is not required
| Environmental
Specifications
|
||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| Operating Temperature | Top | -40 | 85 | °C | Case temperature | |
| Storage Temperature | Tsto | -40 | 85 | °C | Ambient temperature | |
- Serial Communication Protocol
All WINTOP SFPs support the 2-wire serial communication protocol outlined in the SFP MSA. These SFPs use an MCU, can be accessed with address of A0h.
| Serial Bus Timing, Requirements | ||||||
| Parameter | Symbol | Min | Typ | Max | unit | Notes/Conditions |
| I 2C Clock Rate | 0 | 200,000 | Hz | |||
- Mechanical Specifications (Unit:mm)
Specification
Application
Order
| Product Model | Descriptions | Inquiry |
|---|---|---|
| BDTR-FB-P1RC | All WINTOP SFPs support the 2-wire serial communication protocol outlined in the SFP MSA. These SFPs use an MCU, can be accessed with address of A0h. | Request Price |
Downloads/FAQ
Q: May ask this module support IPV6 protocol?
The optical module is only for physical transmission. It has nothing to do with the protocol and can transmit any protocol.
Product Tags
Reviews
0 reviews
5
