4 E1 over Fiber Optical Multiplexer plus Ethernet with GUI management
Short Description:
E1 over Fiber Optical Multiplexer provide E1 and ethernet over fiber transmission, GUI management, double power supplyDescription
Specification
Application
Order
Downloads/FAQ
Product Tags
Reviews
Description
The E1 over fiber optical multiplexer provide 4 E1 and fast ethernet over fiber transmission, which is used to build a 150Mb/s optical point-to-point link. Based on an ASIC chip. The E1 and ethernet over fiber multiplexer also provides an order-wire and an auxiliary UART interface for Management. The fiber multiplexer offers a highly integrated solution for the perfect function, stable performance and convenience with low power consumption. The fiber optical multiplexer can support GUI management, which monitor the device’s operation status. The user also can configure the device easily.
Features
- Merges the Ethernet and time-division multiplex (TDM) transmission to the same pipe.
- Provides 4*E1 and 4*100Mb/s Fast Ethernet interface(sharing same 100M bandwidth).
- The standard E1 interfaces comply with ITU-T G.703, G.823 and G.742.
- Supports either auto-negotiation or hardware configuration selection of the Ethernet operation.
- The Ethernet interface supports VLAN and Flow Control function(set by RS232 NMS).
- The E1 over fiber optical multiplexer support real-time monitoring and all necessary alarm display for easy management.
- Supports Local and Remote Loop-back Test.
- Uses standard telephone set as order-wire(optional)
- Provides one transparent RS232 interface for user’s data links.
- Provides RS232 interface for Network Management.
- The e1 to fiber converter extends the fiber link up to 120 km without any repeater.
- Compact single board Terminal.
- Support power AC (100~220V) or DC (-48V), or double redunctant power AC+DC (optional).
e1 over fiber optical fiber multiplexer GUI management
e1 over fiber optical multiplexer ethernet configuration
E1 and ethernet over fiber multiplexer VLAN configuration
e1 over fiber optical multiplexer status on-line mornitoring
Specification
Optical interface
- Optical wavelength: 850nm/1310nm for multi- mode optical interface,
- 1310nm/1550nm for single-mode optic interface
- Optical interface: SC/FC
- Receiving and dispatching module: >-6dBm
- Optical receiver receiving sensitivity <-36 (BER<10):
- Dynamic range receiving: >-30dB
- Transmitting range:
Multi-mode fiber: 2 Km,
single-mode fiber: 20Km, 40Km, 80 Km,120Km - Vibration characteristic: Satisfies G.742 and the G.823 standard
E1 interface
- Interface code: HDB3 code
- Line speed: 2.048Mbp/S ±50ppm
- Interface standard: ITU-T G 703
- Interface impedance: 75Ω/unbalanced or 120 Ω/ balanced
- Interface characteristic: supports rack (19 inches, 6U high)
10/100M Base-T interface
- Interface rate:10/100Mbps
- Interface characteristic: satisfies IEEE802.3, IEEE802.1Q
- Connector: RJ45
Order wire interface
- Standard two-wire phone
- 64Kb/s PCM coding
- Dial Tone/Busy/Ring Back.
Working condition
- Input voltage: AC220V; AC 110V; DC－48V; DC+24V
- Power consumption: ≤5W
- Operating temperature: 0°C ~ 50°C
- Storing temperature:－40°C ~ +70°C
- Relative humidity: 95 %
Application
Order
| Product Model | Descriptions | Inquiry |
|---|---|---|
| BD-OP-4E1-4ETH/M/AC | 4E1 fiber multiplexer,4*100M Ethernet,75ohm or 120ohm,20km,dual fiber,GUI management,AC220V | Request Price |
| BD-OP-4E1-4ETH/M/DC | 4E1 fiber multiplexer,4*100M Ethernet,75ohm or 120ohm,20km,dual fiber,GUI management,DC48V | Request Price |
| BD-OP-4E1-4ETH/M/AC+DC | 4E1 fiber multiplexer,4*100M Ethernet,75ohm or 120ohm,20km,dual fiber,GUI management,double power AC220V+DC48V | Request Price |
Downloads/FAQ
Qustion: Can the E1 over fiber multiplexer support the GUI/Console management?
Answer: Yes, the manageable fiber multiplexer support GUI/console management. The fiber mux device management is specially designed by our super engineers. Its NMS console management do not input command, the user can configure and monitor the device by GUI. It is very easily operation. (The traditional console management need to input commands, it is not easy to operate ,especially for the general user).
Management Console and Management GUI in PDH Fiber Multiplexer and E1 Protocol Converter
Product Tags
Reviews
0 reviews
5
