Product Overview
BD-FS-81 Optical Fiber Fusion Splicer is small size optical fiber fusions splicer, mainly used for fusion and protection of common communications fibers. The rich functionality and ultra-low splice loss make the splicer adaptive to fiber splicing in various environments. It is featured with small size, light weight, high reliability, greater environmental adaptability, dust-resistant, water-resistant and shock-resistant. Multiple fusion modes and heating modes are available to meet diversified customers’ demands. Fiber loading becomes more convenient and accurate thanks to the ceramic V-groove of high precision, which is easy for clean and maintenance. The splicer is capable of dual-directional fusion. The monitor is a touch screen delivers fresh designed graphical interfaces, which are simple for operation. The modular pluggable lithium-ion battery of large-capacity ensures long-time field operations. The auto environment compensation system greatly improves adaptability of the splicer to hostile environments, so that low-loss splice can be remained consistent in various environments.
Main Characteristics
l Small size, light weight
l 7s fast splicing, 18s highly efficient heating
l 320 times image magnification, 5mm fusing for ultra-short cleave length
l 300 groups of splice modes, 100 groups of heating modes, 10000 groups of fusion records /64 images storage
l Ceramic presser foot, ceramic V-groove, all-in-one fixture
l Dual-directional fusing, auto fusing, intelligent heat shrink
l USB and SD card interface, auto update of U disk
l Built-in modular lithium-ion battery, at least 220 counts of splicing and heating cycles
l GUI (graphical user interface) and touch screen, convenient for operation
l Dust-resistant, water-resistant, shock-resistant, greater environment adaptability
Small and light
Small size and light weight, the splicer is easy to carry and can be lift by one hand.
Water-resistant, dust-resistant, shock-resistant, greater environment adaptability
Meet IP52 requirements.
All-in-one fixer
The all-in-one fixture meet fusion demands of multiple optical fibers, jumpers and rubber-insulted wires with a cladding diameter of 80～150μm.
All-in-one optical fiber fixture
Graphical interfaces and touch screen
BD-FS-81 uses entirely new GUI and touch screen in design. Operators can set up the splicer and get to know relevant information of it simply and directly by graphical interfaces.
Entirely new GUI graphical interfaces and touch screen
Intelligent heat shrink
A detection unit is embedded in the heater. The heating function will only be enabled when the protection sleeve is put in the heater, to avoid mishandling.
Hear and detection unit
Pluggable lithium-ion battery of large-capacity
The built-in pluggable lithium-ion battery of large capacity can answer working demand lasting all day long (typical 220 counts of splicing and heating cycles).
Ceramic V-groove and ceramic presser foot
Ceramic V-groove with high precision brings you convenient and accurate placement of optical fibers and makes cleanup easy.
Carrying case
The carrying case is novel in design and light in weight, has built-in compact working bench. Open or close the cover can turn it to a working bench.
Technical Specifications
| Model | BD-FS-81 Optical Fiber Fusion Splicer
|
| Motor qty | 6 |
| Alignment method | Cladding alignment, manual alignment |
| Applicable fibers | Any common optical fibers, rubber-insulated fibers and jumpers that meet requirements of ITU-TG.651~653, ITU-TG.655 and ITU-TG.657. |
| Optical fiber diameter | Cladding: 80～150μm, coating layer: 0.1～3mm |
| Cleave length | 5～16mm（coated optical fiber diameter≤250μm）；10mm（coated optical fiber diameter：0.25~3mm） |
| Splice loss（typical） | 0.02dB（SMF）; 0.01dB（MMF）; 0.04dB（DSF）; 0.04dB（NZDSF） |
| Return loss | Better than 60dB |
| Splicing time (typical) | 7s (Fast mode) |
| Heating time (typical) | 18s（60mm protection sleeve） |
| Tension | 1.96～2.25N |
| Protection sleeve | 60mm, 40mm and a series of protection sleeves |
| Graphical display | High-performance 4.3 inch LCD |
| Magnification time | 320 times/88 times, 700times |
| Fusion records | 10000 groups |
| Remote maintenance | N/A |
| Battery capacity | 11.1V, 5200mAh |
| Battery service life | Cycle charging: 300～500 counts, can be replaced by customers |
| Electrode service life | Typical: 4000 counts, can be replaced by customers |
| Construction lighting | Built-in lights with high-brightness and wide lighting area |
| Working environment | Temp:-10～50℃；Hum: 0～95%RH，height above sea level: 0～6000m |
| Operation interfaces | GUI (graphical user interfaces) |
| External power | AC: 100～240V, 60Hz, 0～1.5A; DC: 10～15V |
| Port | USB / SD |
| Dimensions | 120mm（W）×130mm（H）×154mm（D）（without rubber anti-vibration pad） |
| Weight | 1.8kg （the battery not included）, 2.1kg（included the battery） |
Standard Package:
| No. | Description | Remarks |
| 1 | Power cord | Standard tri-prong cord: 1 pc |
| 2 | Primary coat stripper | 1 pc |
| 3 | Jacket remover | 1 pc |
| 4 | Spare electrode | 1 pair |
| 5 | Cooling tray | 1 pc |
| 6 | Cleanup set | 1 set |
| 7 | User Manual | 1 copy |
| 8 | carrying case | 1 pc |
Options:
| No. | Description | Functionality |
| 6481B-001 | U Disk | For program update and splice data output |
| 6481B-002 | Lithium-ion battery | Power supply of the main unit |
| 6481B-003 | Power cord of cigarette lighter | Connect to on-board battery, for power supply of the main unit |
| 6481B-004 | Fiber cleaver | To cleave fibers |
Foreign product substitutable:
Sumitomo Fiber fusion splicer TYPE-81C
Related Link:
How many language can Baudcom fiber fusion splicer support?
RFQ:
Question: Can the fiber clamps of the cutter and fusion splicer be disassembled and interchangeable?
Answer: The fiber clamps of the cutter and fusion splicer can be disassembled, but not interchangeable.
Question: Can the fiber clamps of the cutter and fusion splicer be replaced with SOC clamps?
Answer: Yes. It can be replaced with SOC clamps, please confirm the type of SOC clamps before ordering (SOC clamp is an optional accessory and needs to be purchased additionally).
Question: How is the SOC clamp used in the heater of the fusion splicer?
Answer: We will replace the matching heater according to the type of SOC clamp.
Question: There is a SOC clamp that needs to be equipped with a special cutter. If it can cut the normal optical fibers?
Answer: Yes. The special cutter can cut normal optical fibers.
Question: Can the screen of fusion splicer display the types of the fiber while being spliced?
Answer: Yes. The types of the fiber can be displayed on the screen, but not 100% accurate (occurs in all brands of the fusion splicers in the world).